Skip to content
PRD-01Sheet 01 of 06

Helical Gearboxes

Helical gearboxes, sized to the load they will see.

Parallel-shaft and right-angle helical gearboxes for conveyors, mixers and process machinery, designed from your duty cycle and built, run-in and inspected at our works.

Overview

Quiet running starts at the drawing.

We design and build helical gearboxes in one, two and three stages, from a single replacement unit to a series for an OEM's machine range.

Each box starts with the load case. We rate the gears to ISO 6336, check shaft deflection and bearing life against the duty cycle, then cut, grind and assemble in house, so the figure on the drawing is the one you get.

3D render of a steel helical gearbox with its housing cut away to show helical gears, shafts and bearings
Fig. 1Helical Gearboxes

Specification

Spec sheet

MakerTorvik Engineering Pvt. Ltd.
TitleHelical Gearboxes
Part no.PRD-01
01Torque
Up to 12,000 Nm
02Ratio
5:1 to 160:1
03Power
Up to 75 kW
04Mounting
Foot or flange
05Gear quality
ISO 1328 grade 6
06Efficiency
96 % per stage, typical
07Duty
Continuous, service factor 1.5
UnitsSI
ScaleNTS
Sheet01 of 06
NoteQuoted per part, from first article to volume supply.

What each unit is checked to.

  • Grade 6Gear accuracyISO 1328
  • 96 %Efficiencyper stage, typical
  • 72 dB(A)Noise limitat 1 m, on test
  • 2 hRun-inevery unit

Scope of supply

What we make

Rated, not guessed
Gears and bearings checked against your actual duty cycle.
Low noise
Ground helical teeth for smooth, quiet running.
Your ratio
Stage ratios chosen for the machine, not the catalogue.
Run before dispatch
Every unit run-in and checked for noise and heat.
  1. 01One-, two- and three-stage helical units
  2. 02Parallel-shaft and helical-bevel layouts
  3. 03Gear rating to ISO 6336
  4. 04Case-hardened and ground gearing
  5. 05Cast-iron and fabricated housings
  6. 06Bearing selection and life calculation
  7. 07Run-in, noise and temperature check

Case study · Redesign

A quieter drive for a German packaging-machine builder.

  1. 01

    The challenge

    The customer's carton-forming line used a bought-in spur gearbox that was loud on the factory floor and close to its torque limit after a speed increase.

  2. 02

    Our solution

    We designed a two-stage helical unit to the same mounting face and shaft heights, rated it to the new duty, and supplied six pre-production units for trial on the line.

  3. 03

    Customer benefit

    Noise fell by about 6 dB(A) at the operator position, and the unit now ships with each new machine.

Drop-in redesign, series supply

Quality, every batch

Shipped with the report to prove it.

  1. Dimensional reportMeasured results for every characteristic on the drawing, in-process and final.
  2. Material certificateThe certificate for the material used, traceable to the heat.
  3. First article reportA full first-article inspection report (FAIR) signed off before batch supply.
  • Drawings read to BS, ASME and ISO conventions
  • In-process and final inspection, SPC
  • Documented NCR and CAPA closure on every batch

Have a drive that needs sizing?

Send us a brief and we will design it. Send us a drawing and we will make it. Either way you get one team and one point of accountability.

Reference PRD-01 in your enquiry

Next partPRD-02Spur & Ring GearsSpur and ring gears, cut to the grade you specify.