Skip to content
PRD-06Sheet 06 of 06

Shafts & Splined Parts

Shafts and splined parts, turned, cut and ground.

Stepped, splined and geared shafts with matching hubs and couplings, turned, hobbed and ground to drawing, with every diameter that matters measured and recorded.

Overview

The part every gear sits on.

We make drive shafts, splined shafts, pinion shafts and the hubs and couplings that mate with them, to customer drawings.

Splines are hobbed or shaped to DIN 5480 or ANSI B92.1 and checked with go and no-go gauges; bearing and seal diameters are ground after heat treatment. Each batch ships with its measured dimensions and material certificate.

3D render of a stepped steel drive shaft with an involute spline at one end and a keyway at the other
Fig. 1Shafts & Splined Parts

Specification

Spec sheet

MakerTorvik Engineering Pvt. Ltd.
TitleShafts & Splined Parts
Part no.PRD-06
01Diameter
8 to 180 mm
02Length
Up to 1,200 mm
03Splines
DIN 5480, ANSI B92.1
04Ground diameters
To h6, 0.4 µm Ra
05Material
EN19, EN24, 17-4 PH
06Inspection
Spline gauges, full FAIR
UnitsSI
ScaleNTS
Sheet06 of 06
NoteQuoted per part, from first article to volume supply.

What the shop holds.

  • h6Ground diametersbearing and seal seats
  • 0.4 µmSurface finishRa, ground
  • 1,200 mmMaximum length
  • 8 mmMinimum diameter

Scope of supply

What we make

Splines to standard
DIN and ANSI involute splines, gauged on every part.
Ground where it counts
Bearing and seal diameters finished after hardening.
Mating parts
Shafts and hubs made and checked together.
Documented
Measured dimensions and material certificate per batch.
  1. 01Stepped and plain drive shafts
  2. 02Involute splined shafts and hubs
  3. 03Pinion shafts with integral teeth
  4. 04Keyways, threads and cross-holes
  5. 05Induction hardening and nitriding
  6. 06Grinding of bearing and seal diameters
  7. 07Spline gauging and dimensional report

Case study · Second source

Splined shafts for a Dutch agricultural-equipment maker.

  1. 01

    The challenge

    The customer's single supplier of PTO input shafts was running twelve weeks late, and a season's production depended on them.

  2. 02

    Our solution

    We reviewed the drawing, proposed a hardening change to cut distortion on the spline, and ran a first-article batch of 50 with a full inspection report.

  3. 03

    Customer benefit

    The parts were approved first time; we now supply around 2,000 shafts a year alongside the original source.

Approved second source

Quality, every batch

Shipped with the report to prove it.

  1. Dimensional reportMeasured results for every characteristic on the drawing, in-process and final.
  2. Material certificateThe certificate for the material used, traceable to the heat.
  3. First article reportA full first-article inspection report (FAIR) signed off before batch supply.
  • Drawings read to BS, ASME and ISO conventions
  • In-process and final inspection, SPC
  • Documented NCR and CAPA closure on every batch

Have shafts or splined parts to place?

Send us a brief and we will design it. Send us a drawing and we will make it. Either way you get one team and one point of accountability.

Reference PRD-06 in your enquiry

Next partPRD-01Helical GearboxesHelical gearboxes, sized to the load they will see.